Avatar
Please consider registering
Guest
Search
Forum Scope


Match



Forum Options



Minimum search word length is 3 characters - maximum search word length is 84 characters
Register Lost password?
sp_Feed sp_TopicIcon
Model 15-2 cylinder retaining clip question
Avatar
stonebuster
Member
Members
Forum Posts: 298
Member Since:
August 20, 2019
sp_UserOfflineSmall Offline
1
September 15, 2019 - 2:25 pm
sp_Permalink sp_Print

The horseshoe half moon clip that retains the cylinder/yoke assembly from falling out is flat on one side. I believe this is because it needs to be fitted to the gun and requires filing/flattening the clip to fit. Mine is round on one side and flat on the other. Does it make a difference whether the flat surface is facing the front or back of the gun?

Avatar
rwsem
SOWELA (Southwest Louisiana)

Supporter
Members


Moderators


Dans Club
Forum Posts: 5351
Member Since:
February 22, 2009
sp_UserOfflineSmall Offline
2
September 15, 2019 - 4:47 pm
sp_Permalink sp_Print

OEM that I've run across are round stock.  Maybe someone made a clip and had to file it to make it fit the slot...

Technically, the glass is always full; half liquid, half air....

Avatar
3ric
NC
Member
Members
Forum Posts: 607
Member Since:
October 17, 2017
sp_UserOfflineSmall Offline
3
September 16, 2019 - 4:09 am
sp_Permalink sp_Print

No doubt the retainer clip is a homemade replacement, but it probably works fine. I would place the flat side facing towards the front, as there are small flat surfaces there for it to rest against while the rounded surface towards the rear can nest nicely in the groove cut into the lower leg of the crane. 

Avatar
snake-eye
Fort Myers, Florida
Member
Members


Dans Club
Forum Posts: 1967
Member Since:
December 5, 2008
sp_UserOfflineSmall Offline
4
September 16, 2019 - 1:24 pm
sp_Permalink sp_Print

I believe that the flatsided clip is OEM. More of my Dans have flatsided than full round.

Avatar
3ric
NC
Member
Members
Forum Posts: 607
Member Since:
October 17, 2017
sp_UserOfflineSmall Offline
5
September 16, 2019 - 1:44 pm
sp_Permalink sp_Print

Could be. I only own one DW, and it is a very early 15-2 with a round stock clip.

Avatar
hugelk
Northern Illinois
Member
Members
Forum Posts: 392
Member Since:
October 1, 2012
sp_UserOfflineSmall Offline
6
September 16, 2019 - 11:35 pm
sp_Permalink sp_Print

I have found that the flat side is typically installed toward the muzzle. I would say that about half of the DWs I have worked on have clips with a flat of some amount. It seems to be the final fitment of the crane to frame.

Hugelk

Avatar
stonebuster
Member
Members
Forum Posts: 298
Member Since:
August 20, 2019
sp_UserOfflineSmall Offline
7
September 17, 2019 - 9:16 am
sp_Permalink sp_Print

hugelk said
I have found that the flat side is typically installed toward the muzzle. I would say that about half of the DWs I have worked on have clips with a flat of some amount. It seems to be the final fitment of the crane to frame.

Hugelk  

 The final fitment I read about in an old post here when searching and it makes sense. Thanks for confirming that and the orientation of the clip. 

Avatar
jertex
Fort Worth, TX
Member
Members
Forum Posts: 262
Member Since:
February 22, 2017
sp_UserOfflineSmall Offline
8
September 19, 2019 - 10:47 am
sp_Permalink sp_Print

I'm learning a lot by following your trials & tribulations. This will be useful info if anyone runs into similar situations.

Jerry
10 Dans and counting...

Avatar
Charger Fan
Northern Utah

Supporter
Members


Moderators
Forum Posts: 11176
Member Since:
January 24, 2009
sp_UserOfflineSmall Offline
9
September 22, 2019 - 3:03 am
sp_Permalink sp_Print

hugelk said
I have found that the flat side is typically installed toward the muzzle.  

I have found the same, flat side toward the muzzle.

Forum Timezone: America/New_York
Most Users Ever Online: 658
Currently Online: Different Drummer, 605Dart
Guest(s) 78
Currently Browsing this Page:
1 Guest(s)
Top Posters:
Steve: 10330
SHOOTIST357: 4788
Dave_Ks: 4300
Ole Dog: 4086
Stinger: 3465
Supermagfan: 3254
zoommb: 3161
IHMSA80x80: 3014
Blacktop: 3004
brucertx: 2311
Newest Members:
Lavillnon
sfdyaafaasdsdFkds
phique2000
peterodin@msn.com
MarisaFut4580
Brad Merriman
Kennethpem
Jerry
DavidCot
mrpistol43
Forum Stats:
Groups: 11
Forums: 42
Topics: 16855
Posts: 148478

 

Member Stats:
Guest Posters: 87
Members: 11711
Moderators: 4
Admins: 1
Administrators: Jody
Moderators: lbruce, Charger Fan, rwsem, SCORPIO