Register
Log In
Home
October 3, 2017
Offline
I am considering something a bit different from the usual 44 mag loads I shoot. I have heard that the 44 SPL and 44 Russian are fun and a bit more economical for a reloader.
Are there any issues or factors I need to consider? Will either be adversely affecting my cylinders?
--
Hello from Canada.
Supporter
Moderators
Dans Club
February 22, 2009
Offline
My thought/ tip is to invest in a (minimum priced/ used) single stage reloading press and other equipment to reload reduced loads for your .44 magnum. Shooting shorts in the cylinder can cause some issues like carbon buildup and possibly throat deformation depending on how often and what type of bullets you're launching. It's best to stick with brass that the cylinder is milled for- Just my $.02.
Technically, the glass is always full; half liquid, half air....
February 16, 2016
Offline
Just keep the bore clean of lead and powder residue build-up.
October 3, 2017
Offline
rwsem said
My thought/ tip is to invest in a (minimum priced/ used) single stage reloading press and other equipment to reload reduced loads for your .44 magnum. Shooting shorts in the cylinder can cause some issues like carbon buildup and possibly throat deformation depending on how often and what type of bullets you're launching. It's best to stick with brass that the cylinder is milled for- Just my $.02.
I guess I could look around for some reduced loads. Right now I am finishing off my last pound of H110, and was informed that going too low causes some pressure that might be of concern. Maybe it's time to switch to a new powder.
--
Hello from Canada.
Dans Club
December 5, 2008
Offline
I regularly download my 357 and 44 mag rounds. I always use full size brass rather than .38 or 44 spl. That way I don't have to worry about gumming up the cylinders. I have had good luck with Trail Boss powder. It is so large (like a tiny donut) that it's almost impossible to overload the cartridge. A double charge would overflow the brass. You can usually load the powder up to the base of the bullet so long as you don't compress the powder. However, I really have not seen any better accuracy or even much higher velocity than loading at the max recommended by the manufacturer.
I like plated bullets (Berry's for example) and the low powder load does not require a heavy crimp. Too much crimp on plated bullets will strip the plating and degrade accuracy anyway. This setup yields fun shooting and easy cleaning. It's also much cheaper than any factory loaded ammo.
Supporter
Dans Club
March 25, 2013
Online
snake-eye said
I regularly download my 357 and 44 mag rounds. I always use full size brass rather than .38 or 44 spl. That way I don't have to worry about gumming up the cylinders. I have had good luck with Trail Boss powder. It is so large (like a tiny donut) that it's almost impossible to overload the cartridge. A double charge would overflow the brass. You can usually load the powder up to the base of the bullet so long as you don't compress the powder. However, I really have not seen any better accuracy or even much higher velocity than loading at the max recommended by the manufacturer.I like plated bullets (Berry's for example) and the low powder load does not require a heavy crimp. Too much crimp on plated bullets will strip the plating and degrade accuracy anyway. This setup yields fun shooting and easy cleaning. It's also much cheaper than any factory loaded ammo.
Supporter
Range Officer
Moderators
DWF Supporters
Dans Club
December 4, 2011
Offline
I don't like shooting 'shorts' in my guns, I prefer to download full length cases. Carbon ring build up in the chamber throat can cause problems with inserting full length cases in the future. As stout and heavy as the Dan Wesson large frame guns are, I've never felt uncomfortable shooting full power 44 mag rounds. I find accuracy is better with full length cases also, less 'jump' to make it from case mouth to forcing cone.
Anything worth doing is worth doing well.
My father
If a man designed it, and a man built it, then a man can fix it.
My grandfather
1 Guest(s)
